CONTACT US AT 800-321-4726

Riggy-Assist Dual-XLR Preamplifier with Metering (No Phantom Power)

MFR Part #: RA202
Samy's Part #: S-023438
In-store prices may vary
Select Size:
Notice: This item is non-returnable
Special Order
Call to Order: 1-800-321-4726




Items Included

Rate & Review

2XLR inputs low-noise preamp. "Riggy-Assist" means that it has added features to the Riggy-Micro to assist with cameras which do not have headphones, meters, or manual control. It is Riggy in that it has numerous mounting and accessory options (patent pending).  Audio output bracketing (patent pending) for camera overload protection. Alkaline/LiPolymer operation (patent pending).  Selective power-down mode (patent pending). The JuicedLink Riggy-Assist Dual-XLR Preamplifier with Metering (No Phantom Power) takes all of the great features found in the Riggy-Micro RM202, and adds AGC Disable, Headphones, and Meters.

The Riggy-Assist incorporates Audio Output Bracketing (patent pending) for camera overload protection. All of the microphone signals are combined, (by setting the MONO/STEREO switch to MONO), and sent to both the the left and right output channels. The copy on the right output channel is then attenuated to a safe lower signal level (about 16dB lower, by turning ON the Rpad switch). So, if you blow out the main audio channel on the left, you have a back up that you can pull from in post on the right.

This approach has advantages over other types of overload protection, such as limiters. First, Audio Output Bracketing consumes no power from the battery, and also adds no noise or distortion to your audio. Second, every camera gain setting (and, every different camera) will have a unique signal level at which clipping will start to occur. So, if you were to attempt to use a limiter approach, you would need to re-calibrate the point at which the limiter would kick in for each different gain setting of the camera (and, each different camera). Be careful, because not all manufacturers even provide you with the ability to set the limiter threshold setting. Audio Output Bracketing needs no calibration for different cameras or different camera gain settings. The backup channel is always there at ~16dB lower signal level, regardless of the camera or camera gain.

The Riggy-Assist uses a 9V battery, and is a high-current device when all of the elements are in operation. However, the Riggy-Assist has a number of features to allow you to optimize your battery life. Portions of the preamp can be selectively powered down if not being used (patent pending), to reduce the current and extend the battery life. If you are doing a fair amount of running-gunning with only one mic, you can power down 1 of the XLR channels (patent pending). If you are using a camera that has meters visible while recording, you can power down the meter (patent pending). Furthermore, there are very high capacity lithium-polymer batteries on the market, which also have the convenience of being rechargeable.

The low-battery indicator can be switched between alkaline or lithium-polymer threshold, so you can use either chemistry without leaving unnecessary capacity in the battery (patent pending). Battery estimates below. The Riggy-Micro series of preamps (RM202) will get considerably longer battery life, as it does not have the headphone, meter, or AGC Disable circuitry (and, it will be smaller and lighter). The Riggy-Assist is designed to be used with cameras which do not have manual control, meters, or headphones. The preamp adds AGC Disable, meters, and headphones that are missing in the camera. If your camera already has those features, then check out the Riggy-Micro line of preamps. The Riggy-Assist can also be used as a XLR front end to digital audio recorders. Here are some of the many companion devices used with the Riggy-Micro.


  • Two Locking XLR Input Connectors
  • Low-Noise Microphone Preamplifiers
  • 4-Segment Meters can be User-Calibrated
  • Audio Output Bracketing Feature
  • AGC Disable Switch
  • Mic/Line Signal Level Switches
  • Hi/Lo Gain Level Switches
  • 1/8 In. Mono Headphone Output with Level
  • 1/8 In. Output for DSLR Compatibility
  • Powered by a 9V Battery

Customers Also Browsed

  • Saramonic - Universal Audio Adapter for DSLR Camera
  • Saramonic - 2-Channel XLR Audio Adapter for DSLRs
  • Azden - FMX-DSLR Portable Audio Mixer for Digital-SLR Camera
  • Saramonic - 2-Channel XLR Audio Adapter with Isolation Transformer for DSLRs
  • BeachTek - DXA-SLR Pure Passive Audio Adapter for DSLR Cameras
    Special Order
    Call to Order: 1-800-321-4726
  • MyMyk - SmartLynk On-Camera 2-Channel Audio Mixer
  • Zoom - F4 Multitrack Field Recorder with Timecode
  • BeachTek - 2-Channel Active XLR Adapter
    Special Order
    Call to Order: 1-800-321-4726
  • JuicedLink - Riggy-Assist Dual-XLR Preamplifier with Phantom Power and Metering
    Special Order
    Call to Order: 1-800-321-4726
  • Samson - S-amp 4 Channel Stereo Headphone Amplifier
    Special Order
    Call to Order: 1-800-321-4726
  • JuicedLink - Riggy Assist Low-Noise Preamp
    Special Order
    Call to Order: 1-800-321-4726
  • Saramonic - Universal Audio Adapter with Stereo Dual Mono 3.5mm Inputs
Microphones Information
Frequency Response 20 Hz to 20 kHz, +0 /-1.5 dB
Output Connectors 1 x 1/8 In. (3.5 mm) TRS stereo
Battery Type 9V Battery
Dimensions 4.5 x 3.5 x 1.5 In. (114 x 89 x 38 mm)
Weight 9 oz (255 g)
  • 9 In. (23cm) Length, 1/8 In. (3.5mm) TRS Stereo Audio Cable
  • 1/8 In. Hex Key
  • Cork Strip
  • Limited 1-Year Warranty
Be the First to write a Review.
See any errors? Let us know.
Copyright © 2017 Samy's Camera All rights reserved. Terms & Conditions | Privacy & Security Policy
Price, images, specifications and descriptions of items are subject to change without notice. We are not responsible for typographical or photographical errors. Rebates & conditions, and expiration dates from manufacturers are subject to their authorization.